1/4in Hex Bit Holder — 24-Bit 4×6 Desk Tray
A desk-scale tray that holds 24 standard 1/4in hex-shank driver bits upright and organized in a 4×6 grid, at a smaller scale than the bulk wall-mounted 72-bit organizers sold for workshop use.
✓ Full requirement coverage✓ Digitally validated
Key dimensions
| X | 74.04 mm |
| Y | 49.36 mm |
| Z | 28 mm |
About this model
Real 1/4in hex bit holder listings on Etsy target bulk wall-mounted storage (e.g. a 72-bit organizer). A smaller, 24-bit desk-scale tray is a distinct real use case (a driver bit set kept at a workbench or desk, not a full workshop wall board) that the bulk products don't serve.
Fit notes
- 7.34mm hole diameter -- derived from the standard 1/4in (6.35mm) hex shank measured across flats; a round hole must circumscribe the hex cross-section, so the hole diameter is 6.35 / cos(30deg) = 7.34mm, matching how real commercial round-hole hex-bit organizers are sized, plus 1mm clearance
- 25mm pocket depth, a stabilizing pocket for a short bit, not full-length enclosure
- 4×6 layout (24 bits), a desk-organizer scale distinct from bulk 72-bit wall-mounted products
Printing & use notes
No print settings (layer height, infill, supports) are specified for this model — use standard settings for your printer and material. See the validation section below for what has and hasn't been checked.
Validation
Requirement coverage
Full — this model covers the stated requirement completely.
LOW RISK Low risk — simple geometry, loose clearances, not load-bearing.
Digitally validated
- ✓ Geometry valid
- ✓ Matches stated dimensions/spec
- ✓ Manifold (watertight)
- ✓ Slicer compatible
- External manufacturing preflight: not checked
Physical fit and print performance
Physical fit and material/printer-specific performance are not independently guaranteed unless explicitly stated. Physical validation status for this object: not yet physically tested.
MyMakerPilot does not guarantee shrinkage, warping, layer adhesion, strength, real-world load bearing, printer-specific tolerance, or first-print functional usability. Physical printing is optional calibration/sampling, not a publishing requirement.
Technical details
Internal provenance and file references, for anyone who wants the full picture.
- Object ID
- hex-bit-holder-quarter-inch
- Category
- holders
- Risk classification
- low
- External preflight
- unknown
- Physical validation
- unknown
- Production cost
- unknown
- Human review time
- unknown
- STL file
- /objects/hex-bit-holder-quarter-inch/model.stl
- STEP file
- /objects/hex-bit-holder-quarter-inch/model.step
Similar objects
AA Battery Holder Tray — 30-Cell 5×6 Array
A tray that holds 30 AA batteries upright and organized in a 5×6 grid, for bulk battery storage in a count that doesn't match the fixed 16/20/25-count presets sold as ready-made holders.
117×97.5×33mm
AAA Battery Holder Tray — 24-Cell 4×6 Array
A tray that holds 24 AAA batteries upright and organized in a 4×6 grid, for bulk battery storage sized exactly to AAA's own diameter rather than a generic multi-size battery organizer.
93×62×28mm
C Battery Holder Tray — 15-Cell 3×5 Array
A tray that holds 15 C-cell batteries upright and organized in a 3×5 grid, for bulk battery storage in a count that doesn't match the fixed 8/12-count presets sold as ready-made holders.
156×93.6×33mm
D Battery Holder Tray — 10-Cell 2×5 Array
A tray that holds 10 D-cell batteries upright and organized in a 2×5 grid, for bulk battery storage in a count that doesn't match the fixed 8/12-count presets sold as ready-made holders.
196×78.4×38mm