Gridfinity 4×3 Bin Base, 23U Tall (167.5×125.5×161mm)
A tall Gridfinity-compatible storage bin (4×3 grid footprint, 23 units tall) for a toolbox-style build where standard bin heights are too short.
⚠ Partial coverage — see notes below✓ Digitally validated
Key dimensions
| X | 167.5 mm |
| Y | 125.5 mm |
| Z | 161 mm |
About this model
Real demand for a tall Gridfinity bin sized to a specific toolbox footprint and height, from a request that also wanted a cutout for a specific battery -- see "Known limitations" below for what's not included.
Fit notes
- Standard Gridfinity 42mm grid pitch and 7mm per-U height increment
- 1.6mm wall thickness
- Simplified baseplate/bin profile -- does not reproduce the full Gridfinity magnet/screw connector geometry, only the grid-derived footprint and height (see engine/generators/gridfinity.py)
Printing & use notes
No print settings (layer height, infill, supports) are specified for this model — use standard settings for your printer and material. See the validation section below for what has and hasn't been checked.
Validation
Requirement coverage
Partial — this model covers part of the stated requirement. See what's missing below.
- • A battery-footprint cutout requested alongside the base envelope could not be resolved to a specific dimension and is NOT included. This artifact is the base 4x3x23U envelope only.
MEDIUM RISK Medium risk — tight tolerances, thin tall walls, or snap-fit style geometry. Read the notes below before printing.
Digitally validated
- ✓ Geometry valid
- ✓ Matches stated dimensions/spec
- ✓ Manifold (watertight)
- ✓ Slicer compatible
- External manufacturing preflight: not checked
Physical fit and print performance
Physical fit and material/printer-specific performance are not independently guaranteed unless explicitly stated. Physical validation status for this object: not yet physically tested. This is a tall, thin-walled print (161mm) relative to its footprint -- real bed adhesion / warping risk is untested. Flagged medium risk per docs/product-boundary.md's risk gate, not low.
MyMakerPilot does not guarantee shrinkage, warping, layer adhesion, strength, real-world load bearing, printer-specific tolerance, or first-print functional usability. Physical printing is optional calibration/sampling, not a publishing requirement.
Technical details
Internal provenance and file references, for anyone who wants the full picture.
- Object ID
- gridfinity-06
- Category
- grid-storage
- Risk classification
- medium
- External preflight
- unknown
- Physical validation
- unknown
- Production cost
- unknown
- Human review time
- unknown
- STL file
- /objects/gridfinity-06/model.stl
- STEP file
- /objects/gridfinity-06/model.step
Similar objects
Gridfinity Baseplate — Custom 4×3 (168×126mm)
A Gridfinity baseplate at a non-stock 4×3 unit size (168×126mm), for fitting a small or irregular drawer that doesn't match common preset baseplate sizes.
168×126×4.4mm
Gridfinity 1×1 Bin — Loose Electronics Component Storage
A single-cavity 1×1 Gridfinity bin (21mm deep) for loose storage of one small-parts type (e.g. one resistor or capacitor value) per bin, sized to the standard Gridfinity grid so it drops into an existing baseplate.
41.5×41.5×21mm
Gridfinity 2×2 Bin — Loose Hex/Allen Key Storage
A single-cavity 2×2 Gridfinity bin (28mm deep) for loose storage of a hex/Allen key set, sized to the standard Gridfinity grid so it drops into an existing baseplate.
83.5×83.5×28mm
Gridfinity 2×1 Bin — Loose USB/SD Card Storage
A single-cavity 2×1 Gridfinity bin (21mm deep) for loose storage of USB flash drives or SD/microSD cards, sized to the standard Gridfinity grid so it drops into an existing baseplate.
83.5×41.5×21mm