Gridfinity 1×1 Bin — Loose Electronics Component Storage
A single-cavity 1×1 Gridfinity bin (21mm deep) for loose storage of one small-parts type (e.g. one resistor or capacitor value) per bin, sized to the standard Gridfinity grid so it drops into an existing baseplate.
✓ Full requirement coverage✓ Digitally validated
Key dimensions
| X | 41.5 mm |
| Y | 41.5 mm |
| Z | 21 mm |
About this model
Gridfinity-compatible electronics storage bins (for resistors, capacitors, and similar small parts) are a common request across the 3D-printing community. This model covers the simplest, most common form of that need -- one open bin per component type, not a subdivided sorting tray with separate compartments for multiple values.
Fit notes
- 1×1 Gridfinity units (42mm pitch, 0.5mm grid clearance) -- standard Gridfinity footprint
- 3U height (21mm) -- enough depth for a loose pile of small components
- 1.6mm wall thickness (standard Gridfinity bin wall default)
- Scoped to one component type per bin (a single open cavity) by design -- not a subdivided multi-value sorting bin with separate compartments per part type.
Printing & use notes
No print settings (layer height, infill, supports) are specified for this model — use standard settings for your printer and material. See the validation section below for what has and hasn't been checked.
Validation
Requirement coverage
Full — this model covers the stated requirement completely.
LOW RISK Low risk — simple geometry, loose clearances, not load-bearing.
Digitally validated
- ✓ Geometry valid
- ✓ Matches stated dimensions/spec
- ✓ Manifold (watertight)
- ✓ Slicer compatible
- External manufacturing preflight: not checked
Physical fit and print performance
Physical fit and material/printer-specific performance are not independently guaranteed unless explicitly stated. Physical validation status for this object: not yet physically tested.
MyMakerPilot does not guarantee shrinkage, warping, layer adhesion, strength, real-world load bearing, printer-specific tolerance, or first-print functional usability. Physical printing is optional calibration/sampling, not a publishing requirement.
Technical details
Internal provenance and file references, for anyone who wants the full picture.
- Object ID
- gridfinity-bin-1x1-electronics
- Category
- grid-storage
- Risk classification
- low
- External preflight
- unknown
- Physical validation
- unknown
- Production cost
- unknown
- Human review time
- unknown
- STL file
- /objects/gridfinity-bin-1x1-electronics/model.stl
- STEP file
- /objects/gridfinity-bin-1x1-electronics/model.step
Similar objects
Gridfinity 4×3 Bin Base, 23U Tall (167.5×125.5×161mm)
A tall Gridfinity-compatible storage bin (4×3 grid footprint, 23 units tall) for a toolbox-style build where standard bin heights are too short.
167.5×125.5×161mm
Gridfinity Baseplate — Custom 4×3 (168×126mm)
A Gridfinity baseplate at a non-stock 4×3 unit size (168×126mm), for fitting a small or irregular drawer that doesn't match common preset baseplate sizes.
168×126×4.4mm
Gridfinity 2×2 Bin — Loose Hex/Allen Key Storage
A single-cavity 2×2 Gridfinity bin (28mm deep) for loose storage of a hex/Allen key set, sized to the standard Gridfinity grid so it drops into an existing baseplate.
83.5×83.5×28mm
Gridfinity 2×1 Bin — Loose USB/SD Card Storage
A single-cavity 2×1 Gridfinity bin (21mm deep) for loose storage of USB flash drives or SD/microSD cards, sized to the standard Gridfinity grid so it drops into an existing baseplate.
83.5×41.5×21mm